Articles & Resources
-

How to Measure the Effectiveness of Condition Monitoring
Condition monitoring should never be limited to a single technology or method. Instead, it should combine and integrate an optimum selection of purposeful tools and tasks. Condition monitoring can be largely technology based but can also be observation or inspection based. Read More
-

How to Optimize the State of Lubrication
I remember my first day at a new job in 1981. This is the job that launched me into a 32-year career in lubrication. My first assignment was to conduct a telephone survey of industry professionals on various topics related to oil analysis and contamination control. Read More
-

How to Select Machines for Oil Analysis
By Jim FitchMachinery Lubrication Magazine A few years ago, someone mentioned to me that many of his machines were not good candidates for oil analysis because they used little oil that wasn’t worth saving. He added that by the time you flushed the sampling port and pulled a proper oil sample, you’ve almost done an… Read More
-

How to Spot Check Your Car’s Oil
Even the very best motor oils cannot safeguard against sludge when free water is present. Within several minutes after starting an engine, the oil typically reaches the thermostat setting. Read More
-

How to Test Flash Point
Like viscosity, the flash point test has always been a standard part of a lubricant’s specification. And, because of its low cost, simplicity and versatility, the test is popular among the used oil analysis community as well. Most commonly used as a quick pass/fail test for fuel dilution, more applications have surfaced in recent years.… Read More
-

How to Visually Inspect the Health and State of Oil
The well-known KISS principle (keep it simple stupid) was first coined in the 1960s and began widespread use in the U.S. Navy shortly thereafter. While it started as a design principle for engineers, it has since been applied to any activity or creative endeavor that has had the propensity to become unnecessarily complicated. Read More
-
How Water Causes Bearing Failure
By Jim FitchMachinery Lubrication Magazine It takes only a small amount of water (less than 500 ppm) to substantially shorten the service life of rolling element bearings. There is a vast amount of research that supports this. Being a career-long crusader of clean and dry oil, I will certainly not argue the contrary. In fact,… Read More
-

Insider Tips on Managing the Costs of Lubricant Filtration
There is a price tag for removing dirt from oil. For large plants and fleets operating in dusty environments, the cost can be substantial – hundreds of thousands of dollars per year. Read More
-

Intervention is Key to Machine Life Extension
Try this simple experiment. With notepad in hand, go out into your plant and walk around a sampling of your most critical machines. These are the ones that have high probability of failure and/or the greatest consequences of failure. Read More
-

Justifying the Cost of Excluding a Gram of Dirt [the economics of controlling contaminant ingression)
For years Noria has been saying, “The cost of excluding a gram of dirt is probably only about 10 percent of what it will cost you once it gets into your oil.” Recently, a Noria training client asked us to document proof of this statement. Read More
-

Lubricant-Based Techniques for the Condition Monitoring of Non-Circulating Gear and Bearing Systems
The best maintenance techniques for mechanical machinery are condition-based techniques. Condition-based maintenance is maintenance prescribed by the real-time needs of the machine according to changes in specific operation conditions. These conditions fall into two categories. Read More
-

Managing Reliability in Real Time – The Risk Management Grid (RMG)
In a past article,1 I mentioned that in the world of reliability, risk can be defined as the probability of failure multiplied by the consequence(s) of failure. This simple definition should be a reliability team’s most important daily metric. In this editorial, a two-dimensional matrix is proposed that serves as a real-time moving picture of… Read More
-

Managing the Perils of Short-volume Oil Changes
The term “short-volume oil change” (SVOC) relates primarily to circulating oil systems. An SVOC occurs when an oil change (either scheduled or condition-based) only involves draining and refilling the oil in the system tank or sump. Read More
-

Maximizing Fault Detection in Rotating Equipment Using Wear Debris Analysis
The analysis of power train lubricants for the purpose of detecting faults and abnormal wear patterns is a well developed practice in mobile equipment applications. However, these same techniques don’t always transfer successfully into stationary equipment applications for many users. Read More
-

Model of a Fuzzy Logic Expert System for Real-Time Condition Control of a Hydraulic System
Condition control is defined as the interactive processes of condition monitoring, condition analysis, and condition response. A model is presented which employs the use of expert systems to achieve real-time condition control of a hydraulic system. Read More
-

New Lubrication Commandments – Conserve Energy, Protect the Environment
It seems counterintuitive that lubricants selected to optimize wear control may not be optimum when it comes to energy conservation. Read More
-

Oil Sampling Mistakes to Avoid
I recently received an e-mail from a colleague seeking my opinion about a specific sampling philosophy. Referring to mobile equipment such as excavators, scrapers and dozers, he asked if good oil sampling depended much on sampling location. Read More
-

Optimizing Lubrication and Lubricant Analysis
Lubrication is an unmistakably integral part of machine reliability. Rotating machines are dependent on lubrication decisions made, such as which lubricant to use, how the lubricant needs to be applied to the tribological zones, and what is done during operations to monitor and control the integrity of these frictional zones. Read More
-

Origin of Spherical Particles in Lubricants
Spherical particles have been found in microscopic analysis in many different machines. The phenomenon of perfectly round spheres has been a topic of interest since their discovery and a number of theories have been formulated for their origin. Read More
-

Particle Contamination — Both a Cause and a Result of Mechanical Failure
The monitoring of particle contamination in lubricating fluids is a critical indicator of incipient and impending failures. Recent research, under both laboratory and field conditions of the contaminant sensitivity of bearings, reveals a well defined cause and effect relationship between contaminant levels and relative machine life. Read More